Attaches foot rail to bar fronts. (Note: All brackets and are supplied with necessary hardware for proper installation.) Bar Mount Bracket may be boltedfrom back side for additional strength.Measurements (for use with 1-1/2" inch tubing):clearance/projection (CP): 6-1/16"base(B): 4"Measurements (for…
Mount to front and back of Accuride slides for easy installation.
…completely closed, easing it back into position. As with all Blum Tandem slides, these are completely concealed beneath the drawer, allowing you to fully display the grain and workmanship of your wooden drawers. Includes 2 drawer lock mechanisms, screws, and rear brackets for optional face frame installation…
SAVE 33% TODAY!
…handsome brackets! After mounting, sandwich the back edge of any shelf between jaws and tighten to hold in place. When properly mounted to wall studs, brackets support up to 40 lbs. per pair. For shelving 3/16" to 3/4" thick and a maximum of 7-7/8" deep. Jaw opening 13/16" to 25/32".Brackets include wall…
…hampers can mount to the back of a tilt-out door using the separate mounting bracket (sold separately below). The bracket slips into V-notches in the basket, allowing simple removal when it's time to do laundry. The system can also be mounted to the closet wall or to the back of a traditional door, provided…
Hang gallery wraps, canvas and open back frames, and wooden frames flush against your wall with ease using Self-Leveling Flush-mount Hangers! The flush-mount hanger attaches to the back of your canvas using the included 1/2" mounting screws, then self-levels on the included 1-1/2" double-headed screw…
These feet are intended to be paired with our Queen Anne Front Bracket Feet (e.g.33246, sold separately), and are sold and shipped in left/right pairs. All are carefullycarved from 1-1/8" thick x 4-1/2"H stock with an ogee profile and a 3/4" flat on top.All measure 6"W x 4-1/2"H.
These feet are intended to be paired with our Chippendale Front Bracket Feet (e.g.31132, sold separately), and are sold and shipped in left/right pairs. All are carefullycarved from 1-1/8" thick x 4-1/2"H stock with an ogee profile and a 3/4" flat on top.All measure 6"W x 4-1/2"H.
Fence Backstops provide extra height for the back of the Best Fence. Brackets flip forward onto the fence and slide into position, then flip back to cam solidly into place. Attach different boards between the two brackets for as much or little support as you need!See the Best Fence v3 System here.
These Upper Extension Brackets will come in handy when you're adding wooden upper supports to your Panel Pro 2 Panel Saw! The brackets attach to the back of the frame, making it possible to add a couple of 2 x 4s and keep your sheet goods stable while ripping or cross-cutting.
…drawers. Set includes black metal 13" front and back rails, 22" cut-to-size side rails, cut-to-size brackets, and side-to-side rail.Easy to adjust between filing configurations - rails snap in and out of position without tools. Able to withstand thousands of back and forth cycles. Accommodates letter, legal…
…units for home theater, computer or other electronic components.System extends full 20" and rotates 90° in both directions for complete access to the back of shelving units.
4-Foot Radius-Back Channel for 1/4" GlassMeasurements (for use with 1-1/2" inch tubing):height(A): 1/2"width(B): 1/2"thickness(T): 0.0940"
…standards and six sturdy 14" brackets to make three adjustable shelves that support up to 300 lbs. per shelf! It's the perfect lumber rack to keep just above your miter saw for easy access when cutting rippings to length. Fasten it to the wall at whatever height is easiest on your back, or at eye level to make…
…travel. These over travel slides also feature convenient lever disconnect and impeccable construction. Includes mounting hardware and instructions. Back brackets (47585, sold separately) are required for mounting to face frame cabinets.
…pens and pencils-check. A couple of trays for Post-Its and paper clips-check. And a vast space in back for paper-check! Add smooth, integrated ball-bearing slides and easy mounting with the included brackets, and this pencil drawer becomes a shoo-in for home or office use.
…thatmeets the floor. The feet can be used on either the left or right side by simply turning90 degrees, and pair perfectly with our Queen Anne Back Bracket Feet (e.g. 33989. soldseparately). Each order includes triangular corner blocks to be used if extra support isneeded. All feet are carefully carved…
…thatmeets the floor. The feet can be used on either the left or right side by simply turning90 degrees, and pair perfectly with our Chippendale Back Bracket Feet (e.g. 39515. soldseparately). Each order includes triangular corner blocks to be used if extra support isneeded. All feet are carefully carved…
Radius-Back Clip for 1/4" GlassMeasurements (for use with 1-1/2" inch tubing):width(W): 1-3/8"height(H): 1-3/4"
Securely mount large or small items to any solid surface with Piranha Lox! A simple flip of the lever lets you remove the item from the mounted backing plate or reinstall it in seconds. Use it to securely lock flat screen TVs, pictures, tool boxes, and more in place. Has a rust-resistant finish and is…
…. Mechanism uses a sophisticated piston lift system rather than old-fashioned springs that can snap back. Beds are held securely closed, and open gently for added safety. Steel pivot pin and bracket points install easily without adjustments. Includes instructions for basic cabinet construction and instructional…
A simple way to secure cabinet doors. Cam Lock adjusts for varying door thickness. Mounting bracket adjusts for 3/4" to 1-3/8" thick panels. Back mounting design.
…Included peel-and-stick sensor strips mount to the tracks with adhesive backing and supply the sliding readout unit with positional data. Digital readout displays measurements in decimal and fractional inches or millimeters. Mounting bracket, hardware and alignment gauge included.