Plastic Preglued Edge Banding is a two-ply polyester edgebanding material with a hot melt adhesive backing, allowing easy application with a household iron. It is very flexible, accommodating both inside and outside curves, and is ideal for taping the raw edge on melamine or Formica sheet goods and…
$7.00
Use 3/4" molding for plywood, and 13/16" molding for laminated sheet goods. 3/4" wide molding requires a 1/16" kerf. 13/16" molding requires a 5/64" kerf.Wraps around a radius as small as 1-1/2". To fit a 90 degree corner, just clip the ribbing that fits the groove.Available in four different…
From $15.49
…the edge of your blade or cutter.Ideal for use with all Universal T-Tracks, Multi Tracks, and Double T-Track Fence Caps. Each tape comes with an acrylic hairline indicator with adhesive backing that can be attached to Rockler Flip Stops (26991 and 31214) or other homemade stops. Inserts are plastic extrusions…
From $10.99
…Simply place the end trimmer on the end of the panel and firmly press the lever down. You'll get a high-quality cut on all corners of the board! Plastic body. Two (upper and lower) high speed steel blades.
$44.49
…with cabinet drawer openings that have a center, T-shaped guide rail. The set consists of one adjustable center-mount plastic backplate and two L-shaped nail-on glides for drawer edges. Backplate adjusts to fit guide rails from 1" to 1-7/16" wide.
$4.59
…be shimmed in .010" increments when using the router table to edge-joint boards.Shims can be combined to shave .070" off an edge. Designed for use with the Rockler router table fence.Shims measure 2" high x 14" long.Includes six plastic shims in these thicknesses: four each of .010" gray, one each of…
$6.99
…smooth edge without clogging or heat buildup. Rotary shapers have razor-sharp teeth that quickly shave wood without clogging or heat buildup.Creates shavings - not dust!Hardened stainless steel. 5/16" shank.Can be used at speeds up to 2500 RPM.Easy attachment to drill press.For use on wood, plastic and…
From $17.99
…drilling through drywall to feed low-voltage cables and wires through the wall smoothly for a simple and organized look. Bushings finish cut drywall edges and prevent crumbling when cables are pulled through or adjusted. Available in three sizes, as listed.
From $1.59
…distance from the material edge in increments of 1/10mm for ultra-precise routing. Dust extraction hood enables ultra-efficient dust extraction, saving valuable cleanup time. The Edge Guide is constructed from durable cast aluminum, and includes fiber-reinforced plastic thumbscrews for easy adjustment…
$75.00
…acrylics, polycarbonates and other plastics, leaving a smooth finish without melting. By combining micrograin carbide tips with a specially modified triple chip grind these blades will give a clean smooth cut. These blades produce less heat keeping the cut edge crisp. The Silver I.C.E. (Industrial…
From $61.47
…cutting non-ferrous materials, especially aluminum; also useful for acrylics and hard plastics. The Aluminum/Plastic Cutting Blade incorporates a TC (Triple Chip), or trapezoidal flat tooth saw blade design, wherein the edges of alternating blade teeth are beveled on both sides. These beveled teeth alternate…
$135.00
…carbide tipped Aluminum/Plastic Cutting blade for the TS 55 Plunge Cut Saw is designed to cut non-ferrous materials, especially aluminum; also useful for acrylics and hard plastics. This blade incorporates a TC (Triple Chip), or trapezoidal flat tooth saw blade design, wherein the edges of alternating blade…
$90.00
…Fine-adjustment control allows you to dial in the distance from the material edge in increments of 1/10mm for ultra-precise routing. The Edge Guide is constructed from durable cast aluminum, and includes fiber-reinforced plastic thumbscrews for easy adjustment and a long service life. Attaches quickly and…
$55.00
The versatility of these hard edge flex back blades is unmatched. Get perfect cuts every time in hardwoods, softwoods, plastic, mild steel, and non-ferrous metals. Blades feature a hard-edge flex back. Available in regular, skip, or hook teeth in three lengths: 72-inch for Shopsmith or similar models…
From $15.79
…templates. Includes 1/2" and 1/4" Dovetails, a Stanley F 3, Butt Hinge, Lock Face, two general bushings, and two locking nuts. All fit in a convenient plastic case.
$43.99
…and edge has fine grit. Flexible core conforms nicely to turnings, moldings and other non-flat surfaces. They also work well on flat surfaces, especially between coats of finish, where a harder block would sand through the finish. Ideal for light to moderate sanding of wood, paint, metal, plastic and…
$5.29
These hook-and-loop sanding discs are made with a tear-resistant film backing for better edge wear and a longer life. They are feature an anti-clog coating that helps the abrasives last up to 4 times longer than traditional sanding discs. For use on wood, metal, fiberglass and painted surfaces.
$9.99
The rounded edges on the lid of this maple pen box give it a soft feel, while the display hole keeps your pen handy when it's needed. Solid hard maple body with mahogany trim. Pen boxes are shipped with a smooth, semi-gloss finish. Whisper-quiet lid features full 180 opening, perfect for showing off…
$7.99
…the Drill Guide Kit. The drill guide kit allows you to insert a steel bushing into the plastic guide and your drill will bore perfectly perpendicular holes. An ingenious design also centers your drill bit on edges. The drill guide kit also works to drill holes on spheres and cylinders.
$15.49
…The saw blade retracts into the housing, which makes cuts in the middle of a sheet precise, easy, and safe. Ingenious bevel-tilt mechanism keeps the edge of the guide rail precisely on the cut line, regardless of the bevel angle. Ideal for heavy sheet stock, since you can take a lightweight tool to the…
$695.00
Bailey® Block PlaneBailey® Block Plane Ideal for planing end grain and plastic materials12-920 block plane has a fully adjustable cutter resting at 2113-1/2 low angle cutter on the 12-960 block plane keeps vibration to a minimum, creating a fine finishGray, cast-iron base with precision-ground sides…
$59.99
…attaches to the end of the guide rail without the need for tools. Features wings on the outside edges to help keep the hose and cord properly positioned and out of your way. Made of nylon reinforced plastic for a long service life. Includes 1 Hose and Cord Deflector.
$18.00
Cut thin wood, plastic, fiberglass, non-ferrous metals, thin sheet metal, hardened fillers, window glazing and more with this 3-1/8" HSS Circular Saw Blade. The circular profile provides more usable cutting edge for a long life, and allows cuts from a full 360 angle of approach. Flat side allows you…
From $13.49
|
Need Help? |
(0 Items)